Compare quotes from multiple verified Battersea plumbers
Your enquiry goes straight to the plumbers you pick — no middleman fee
Find a verified plumber for kitchen work across Battersea (SW11, and the SW8 edge) — sinks and taps, waste and traps, isolation valves, water-softener and filter set-ups, and the plumbing side of a new or refitted kitchen. Listings show what each plumber covers.
✅ Checked before listing — identity, insurance, trading presence, Gas Safe (where relevant).
✅ Workmanship guarantee badges on listings — 1, 3, 6 or 12 months
Swapping a tap, moving a sink and plumbing a whole new kitchen are different jobs at different prices. Ask the plumber to confirm call-out, labour and parts in writing before work starts. Your enquiry goes straight to the plumbers you pick — no per-enquiry middleman fee.
Contact verified plumbers in Battersea ↓
Are you a plumber covering Battersea?
Use the search above to find a local expert
Coverage: Battersea SW11, plus the SW8 edge (Queenstown Road, Nine Elms, Battersea Power Station). Confirm your postcode when you call.
What this covers: Kitchen sinks, taps (including pull-out and boiling-water taps), waste, traps and standpipes, isolation valves, water-softener and drinking-water-filter set-ups, and the supply/waste side of a kitchen refit. Plumbing in a washing machine or dishwasher has its own page; new kitchen circuits are separate, notifiable electrical work; other kitchen electrical work may be non-notifiable but must still comply with Part P.
If it’s really something else: connecting the machine is Washing Machine & Dishwasher Installation in Battersea; a single failing tap is Tap Repair & Installation in Battersea; a sink that won’t drain or a gully backing up is Blocked Drains in Battersea.
Costs: A refit’s plumbing is priced per project — get it itemised in writing. See the estimate table below.
Availability: Varies by listing; refits are booked ahead. Confirm lead time when you call.
What kitchen plumbing actually covers
A kitchen is unusual: it’s the room where you drink the water and where a lot of the house’s waste leaves. That dual role sets the rules.
The waste and the trap. Under GOV.UK’s Approved Document H, a kitchen sink needs a 40 mm trap with a 75 mm water seal, with the branch run to the stack kept within length limits so the seal doesn’t siphon dry.1 On a sink island away from the stack, the plumber should check branch length, fall and ventilation; a long or poorly vented run can siphon the trap and may need an air-admittance valve or another compliant venting arrangement. Forming a new waste connection must comply with Approved Document H, but does not by itself make every job notifiable; Building Control involvement depends on the wider work.
The tap and backflow. A kitchen tap needs an air gap above the sink’s spill-over level to prevent backflow — under WRAS installation requirements a standard kitchen tap achieves this with an AUK3-type air gap, while pull-out spray and hose taps need an installation-specific backflow assessment. Product approval alone is not a substitute for protection appropriate to the actual fluid risk, and any approval conditions must be followed.2 It’s the sort of detail that’s invisible until a water inspector or a contamination problem finds it.
The electrics. A kitchen is not a defined special location under the current notification rules. Under GOV.UK’s Approved Document P, a new circuit is notifiable wherever installed, but adding a socket or spur to a suitable existing circuit or connecting an integrated appliance is not automatically notifiable merely because it is in a kitchen.3 All electrical work must still comply with Part P and BS 7671. A plumber can fit the tap; the dedicated circuit for it is an electrician’s job.
Hard water, the drinking-water tap and Battersea’s kitchens
This is where hard water becomes a decision, not just a nuisance. Battersea’s supply from Thames Water is classified as hard.4 Where an ion-exchange water softener is being considered, its effect on the drinking-water supply must be addressed. But there’s a rule that catches people out: the Drinking Water Inspectorate advises keeping an unsoftened supply to the kitchen tap for drinking and cooking, because ion-exchange softeners work by adding sodium — a concern for infants and anyone on a low-sodium diet — and the drinking-water regulations set a sodium standard a softener could risk breaching.5 Where an ion-exchange softener is installed, retain a kitchen drinking-water outlet supplied from the unsoftened mains. Getting that plumbed correctly is an important installation detail — not a sales add-on. (Thames Water make the same point: if you fit a softener, keep a separate tap for drinking and cooking.)
The stock still decides the work:
In some new-build riverside kitchens around Nine Elms and Battersea Power Station, integrated appliances, fixed cabinetry and building isolation procedures can restrict access. Check the building specification and managing agent before adding a filter, boiling-water tap or softener; inaccessible valves or service space can make the first visit diagnostic only.
In the terrace kitchens (Northcote Road, Lavender Hill, Falconbrook, Shaftesbury & Queenstown), a refit or a rear “kitchen-diner” extension can mean new waste runs and moving the sink, which is where the Part H trap and branch-length rules bite.
In privately rented properties, a between-tenancy tap or sink swap may be straightforward, but the trap and isolation valves should still be checked rather than inheriting a previous defect. In a flat above a shop around Lavender Hill or Battersea Park Road, an active leak may need immediate containment and coordination with the landlord and commercial occupier below before a shared supply is isolated. Test isolation valves and flexible connectors first, then trap joints and appliance spigots; fixed cabinets, worktops or a seized valve may limit the first visit to diagnosis or temporary isolation.
Honestly: the sink/waste and softener rules are national. Where a softener is proposed, the unsoftened drinking-water outlet must be planned; where a refit moves the sink, the waste route and any communal-stack connection must be checked before units are fitted.
Find a verified kitchen plumber by district
Coverage varies by listing — confirm your postcode when you call.
Nine Elms & Battersea Power Station riverside — SW11 / SW8Kitchens in newer blocks may have integrated appliances and restricted service access; confirm the fitted arrangement. Possible work includes filter or boiling-water taps and, where proposed, softener set-ups that respect the confirmed block-isolation arrangement while keeping the drinking tap on unsoftened mains; communal supply issues go to building management.
Central Battersea & Battersea Park — SW11Battersea Park ward and the mansion blocks off Prince of Wales Drive. Mansion-block kitchens can share communal waste stacks, so a new sink position has to tie in without affecting neighbours; some works need managing-agent consent.
Clapham Junction, Winstanley & York Road — SW11 (Falconbrook ward)Victorian terraces plus regenerating estates. Terrace kitchen refits and rear extensions can involve a new waste run — Part H trap and branch-length rules apply, and it’s the point where corners get cut.
“Between the commons” terraces — SW11 (Northcote, Lavender)Where a family house off Northcote Road is being renovated or opened into a kitchen-diner, confirm both the unsoftened drinking-water outlet, if a softener is proposed, and the new waste route before the units go in — retro-fitting either is dearer.
Where a line would read identically for any trade, it’s been dropped — the kitchen-specific point is the softener/drinking-tap decision and the moved waste run.
What kitchen plumbing costs in Battersea
| Scenario | Typical range |
|---|---|
| Swap a kitchen tap (like-for-like) | £80–£180 |
| Supply & fit a new sink + tap (excl. worktop) | £150–£380 |
| Fit a boiling-water tap (plumbing; excl. electrics) | £150–£350 |
| Install a water softener + retain unsoftened drinking tap | £500–£1,200 |
| Move sink / new waste run for a refit or extension | £250–£700 |
| Kitchen refit — plumbing labour (excl. units/appliances) | £600–£1,800+ |
Editorial estimate only, observed across independent WaterSafe and general plumbing contractors and directories in early 2026. Not regulated rates, not market data, not based on a published cost survey. Battersea is inside the London-wide ULEZ (from 29 August 2023) but outside the central Congestion Charge zone.6 Appliance connection and electrical work are separate line items — get them itemised.
Frequently asked questions
It can be considered because the water is hard, but it is not a universal requirement. The Drinking Water Inspectorate advises keeping an unsoftened supply to the kitchen tap for drinking and cooking, because softeners add sodium — a concern for infants and anyone on a low-sodium diet. If an ion-exchange softener is installed, retain a separate kitchen outlet supplied from the unsoftened mains for drinking and cooking.
The DWI’s position is to keep the drinking and cooking tap unsoftened. For most healthy adults the extra sodium is small, but the advice exists specifically to protect infants and people on low-sodium diets, and softened water can also be more aggressive to copper and lead pipework. Use a separate kitchen tap supplied from the unsoftened mains; an ordinary filter is not a substitute because it may not remove the sodium added by ion exchange.
The plumbing, yes. If the boiling-water tap needs a new dedicated circuit, that circuit is notifiable under Approved Document P. Connection to a suitable existing circuit is not automatically notifiable merely because it is in a kitchen, but all electrical work must comply and should be assessed by a competent electrician. Many plumbers pair with an electrician for this. Before quoting, check pressure and flow, cupboard space, isolation, electrical readiness and service clearance. A fixed worktop, restrictive cabinet or seized isolation valve may make the first visit a survey or temporary-isolation visit rather than a completed installation.
Bigger than it looks. Moving a sink means a new waste run, and Approved Document H sets the trap (40 mm / 75 mm seal) and how far the branch can run before it needs venting or an air-admittance valve. On an island, the plumber should check the fall, branch length and ventilation: an excessively long or poorly vented run can siphon the trap and may need an AAV or another compliant venting solution. Plan the route before the units go in.
Hard water. Battersea’s supply is classified as hard, so aerators and cartridges scale up. For a pull-out spray tap, check the fitted arrangement, hose reach and any product-approval conditions so the installation provides protection appropriate to the actual fluid risk. Descaling helps; a quality tap with serviceable parts lasts longer here.
A kitchen plumber should check the trap, branch fall and length, ventilation or air admittance, and downstream restriction. If several fixtures or flats are slow to drain, the restriction may be in a communal branch or stack and should go through the managing agent; an external gully or wider drain backup belongs with Blocked Drains. For odours, first confirm that the trap holds water and is not being siphoned; an odour affecting several fixtures points more strongly to a downstream ventilation or drainage problem than to one kitchen trap.https://verifiedplumbers.co.uk/london/wandsworth/battersea/blocked-drains/
Why verified plumbers — not a general directory
The kitchen is the one tap in the house you actually drink from, which is exactly why the softener-and-drinking-tap detail matters — and why the waste and backflow, done wrong, cause contamination and blockages you don’t see coming. That’s the case for a plumber whose credentials have been checked.
Every listing is checked before it goes live and re-verified annually: we confirm the business is legitimately trading and verify the named contact, we check evidence of public liability insurance, and we confirm the plumber covers Battersea’s SW11 and SW8 postcodes before a profile is approved. Because kitchen work is water-fittings work, you can also look a plumber up yourself on WaterSafe, the free, water-industry-backed national register.
Profiles may be suspended or removed if credentials lapse or credible concerns are raised — see the full verification process →. Listing is a flat monthly fee with no pay-to-play ranking, and there’s no customer middleman fee: enquiries go directly to the plumber.
Related areas
Verified plumbers across Battersea’s neighbourhoods, including:
Battersea Park
Battersea Power Station
Clapham Junction
Lavender Hill
Nine Elms
Queenstown Road
Shaftesbury Estate
Winstanley / York Road
Related services
Other verified plumbing services in Battersea:
Emergency Plumber in Battersea
Tap Repair & Installation in Battersea
Bathroom Plumbing in Battersea
Washing Machine & Dishwasher Installation in Battersea
Boiler Installation in Battersea
Central Heating Repair in Battersea
Commercial Plumbing in Battersea
Related guides
New Homeowner Plumbing Guide — London 2026
London Hard Water — The Complete Homeowner & Landlord Guide 2026
How to Read a Plumbing Quote — A London Homeowner’s Guide 2026
London Plumbing Costs & Compliance Guide 2026
A good Battersea kitchen gets two things right that most people never think about: the drinking tap stays on unsoftened mains even when the rest of the house is softened, and the waste is trapped and run so it never siphons dry. Match the listing to the job — a tap swap, a softener set-up, or a full refit — and get the plumbing itemised in writing before the units go in.
Contact verified plumbers in Battersea ↑
← Back to all plumbing services in Battersea
Last reviewed: July 2026 by Adiel Khan — SFEDI-accredited business advisor, 20+ years’ experience (South East Enterprise Ltd) and operator of VerifiedPlumbers. LinkedIn ↗
This page is checked for compliance and regulatory accuracy against the Water Supply (Water Fittings) Regulations 1999, WRAS installation requirements, Building Regulations Approved Documents H and P, BS 7671, the Drinking Water Inspectorate, Thames Water and Transport for London. Source links are provided within this page where relevant.
Sources & further reading
GOV.UK — Approved Document H, Drainage and Waste Disposal (40 mm trap with 75 mm seal for a kitchen sink; branch-run and venting requirements).
WRAS — Installation Requirements (tap-gap and product installation requirements; product approval does not replace installation-specific backflow protection appropriate to the fluid risk).
GOV.UK — Approved Document P, Electrical Safety (new circuits and consumer-unit replacement are notifiable; ordinary additions to existing kitchen circuits are generally non-notifiable, though all work must comply with Part P).
Thames Water — Hard water (London supply classified as hard; keep a separate tap for drinking/cooking if a softener is fitted).
Drinking Water Inspectorate — Domestic water filters and softeners (retain an unsoftened supply to the kitchen tap for drinking and cooking; softeners add sodium and may risk the drinking-water sodium standard).
Transport for London — Ultra Low Emission Zone (London-wide ULEZ from 29 August 2023).
Wandsworth Council — Constituencies and wards (current ward geography covering Battersea).