Compare quotes from multiple verified Welling plumbers
Your enquiry goes straight to the plumbers you pick — no middleman fee
The kitchen is the one room where the plumbing and the drinking water meet, so getting the sink, the wastes and the cold drinking tap right matters more than it looks. These are plumbers covering Welling and the wider Bexley area, each checked before being listed, so you can contact one directly.
✅ Checked before listing — identity, insurance, trading presence, Gas Safe (where relevant). How we verify →
✅ Workmanship guarantee badges on listings — 1, 3, 6 or 12 months
Typical Welling kitchen jobs run from around £120 to fit a sink and tap up to several hundred for wastes and feeds after a refit — see what it costs below.
Contact verified plumbers in Welling ↓
Are you a plumber covering Welling?
Use the search above to find a local expert
Coverage: Welling’s DA16 postcode — the High Street, Crook Log, Bellegrove, Falconwood and the East Wickham edge.
What this covers: kitchen sinks, taps, wastes and traps, appliance feeds and connections, water filters and softener plumbing, and re-plumbing after a kitchen refit.
Not sure this is the right page? For a washing machine or dishwasher see Washing Machine & Dishwasher Installation; for a dripping tap see Tap Repair & Installation.
Costs: indicative Welling ranges are under What it costs — editorial estimates only.
Availability: each plumber sets their own hours — shown on their profile.
Jump to: What kitchen plumbing involves · The drinking tap, hard water and backflow · By area · What it costs · FAQs
What kitchen plumbing involves
Kitchen plumbing is mostly about the sink and the appliances behind the units. Refits are a common point at which disturbed or newly routed connections begin to leak or drain poorly.
The sink and waste need a suitable trap and a waste run with an adequate fall. For a slow sink, the plumber should inspect the trap, check the branch for grease or food debris, verify the fall and then test the downstream connection. Long or shallow runs can retain grease and may need cleaning before the underlying fall or ventilation can be assessed. An island sink needs its branch length, floor depth and ventilation assessed; an air-admittance valve can be one design solution, but it is not an automatic cure and must remain correctly positioned, ventilated and accessible. Appliance feeds need accessible isolation and backflow protection selected for the appliance and fluid-category risk. After a refit, feeds, valves, hoses and wastes should be tested under operating pressure before units are closed. To distinguish a supply leak from a waste leak, the plumber can first observe the connections with the sink unused, then discharge water and inspect the trap and branch. Isolation valves should be tested, and appliance hoses and flexible tap tails checked for twisting, abrasion or excessive bending while the appliance is running and before it is pushed fully back. Before fitting a boiling-water or specialist filtered tap, the available pressure, flow and accessible isolation should also be confirmed.
A verified plumber sets the wastes and feeds out before the units go back, because access under a fitted kitchen is the first thing you lose.
The drinking tap, hard water and backflow
The drinking-water tap. The Water Supply (Water Fittings) Regulations 1999 require at least one conveniently situated tap from which wholesome water can be drawn for drinking; the permitted supply is not limited to a tap directly connected to the mains or located at the kitchen sink.1 If a water softener is fitted, the Drinking Water Inspectorate advises retaining an unsoftened supply to the kitchen tap used for drinking and cooking because ion-exchange softeners add sodium and softened water may be unsuitable in some circumstances.2
Hard water. Welling is in Thames Water’s hard-water region,3 so limescale can affect aerators, tap cartridges and water-using appliances. Poor tap flow can also result from debris, partially closed isolation valves, restricted flexible hoses, pressure problems or cartridge faults, so the cause should be checked before a part is replaced.
Backflow and connections. Kitchen fittings and appliance water-supply connections require backflow protection selected for the appliance and the applicable fluid-category risk under the Water Fittings Regulations.4 Waste must connect to the foul system; foul-to-surface-water misconnections are unlawful where separate systems are provided and can pollute watercourses.5 A new kitchen circuit is notifiable under Part P. A fused spur added to an existing kitchen circuit is generally non-notifiable unless another notifiable category applies. All electrical work must comply with Part P; designing and testing it to the current BS 7671 is the standard route to demonstrating compliance.6
Find a verified kitchen plumber by area
Welling High Street & Crook Log (DA16 1) — in flats above shops, several appliance connections may be crowded into a compact kitchen and access to a shared riser may be controlled by a managing agent. A leak can disrupt the commercial premises below, so isolation and pressure testing matter before units are closed. In takeaway or hospitality premises, grease control, access to the waste run and business downtime also need to be planned.
Bellegrove & the town-centre streets — in a rear extension or altered kitchen, the plumber should confirm that there is enough floor depth and route length to achieve a suitable gravity fall back to the original connection. Where that cannot be achieved, the layout needs redesign rather than assuming an air-admittance valve will solve it.
Falconwood & the Danson side (DA16 2/DA16 3) — where a softener or filter is proposed, the plumber should confirm the drinking-water arrangement, bypass and isolation points and keep them accessible; the need for a softener is property-specific rather than an area-wide assumption.2
East Wickham edge — in older kitchens, later fitted units may conceal the internal stop tap, isolation valves or the original waste route. Access should be confirmed before work starts, and a leak may need temporary isolation if the correct valve or hose is not immediately available.
What it costs
| Job (Welling / DA16) | Typical indicative range | Notes |
|---|---|---|
| Fit a kitchen sink and tap | £120–£300 | Plus the sink/tap if supplied |
| Connect appliances & waste after a refit | £120–£350 | Depends on number of feeds |
| New waste / trap run (incl. island / AAV) | £150–£400 | Route- and floor-dependent |
| Fit a water filter or softener (plumbing) | £150–£400 | Drinking tap kept unsoftened |
| Relocate kitchen feeds and wastes | £250–£700+ | Larger refits and layout changes |
Editorial estimate only. These figures are not regulated rates, not market data and not a published cost survey — a general guide; actual quotes vary by job, access and spec.
Welling is inside the London ULEZ, so a non-compliant van may carry the daily charge; it is outside the central London Congestion Charge zone.7 ULEZ rules can change, so check the current position.
Frequently asked questions
Keep the kitchen tap used for drinking and cooking on an unsoftened supply. The DWI advises this because ion-exchange softeners add sodium and softened water may be unsuitable in some circumstances.2
Limescale can restrict an aerator or cartridge in a hard-water area, but debris, isolation valves, flexible hoses, pressure and cartridge faults should also be checked.3
The plumber should inspect the trap, branch length, fall, ventilation and downstream connection. An air-admittance valve may be appropriate in some layouts, but only if it is correctly positioned, accessible and compatible with the wider drainage ventilation.
Like-for-like fittings are generally maintenance. New or materially altered drainage may require Building Regulations approval and should be checked with building control; Approved Document H describes compliant drainage design. A new kitchen circuit is notifiable under Part P, while a fused spur added to an existing circuit is generally non-notifiable unless another notifiable category applies.86
Yes, commonly via a suitable sink-trap appliance spigot. The potable-water connection must have the backflow protection appropriate to the appliance, while the waste hose and trap connection should follow the appliance manufacturer’s instructions. Incorrect hose routing, an open unused spigot or trap siphonage can cause odours or allow wastewater to return towards the appliance.
—
Why verified plumbers — not a general directory
Kitchen connections are often concealed once fitted units and appliances are in place. A verified, insured plumber should set out and test the feeds, isolation points, hoses, traps and wastes before access is closed.
Every listing is checked before going live and re-verified annually: we confirm the business is legitimately trading and verify the named contact, we check evidence of public liability insurance, and we confirm the plumber covers Welling’s DA16 postcode before a profile is approved — and we keep an eye on customer feedback gathered from across the web. For water-fittings and softener work you can also look a plumber up yourself on WaterSafe, the free, water-industry-backed national register; where a job involves gas we confirm Gas Safe registration directly with the Gas Safe Register.
Listed plumbers pay a flat monthly fee to be listed. What that fee never buys is the verification itself — every listing is checked on the same terms — and there’s no per-enquiry middleman fee, so your enquiry goes directly to the plumber. Profiles may be suspended or removed if credentials lapse or credible concerns are raised; see the full verification process →.
Related areas
Verified plumbers across Welling’s neighbourhoods and nearby areas, including:
- Belle Grove
- Bexleyheath
- Blackfen
- Crook Log
- Danson
- East Wickham
- Falconwood
- Shooters Hill
Related services
Other verified plumbing services in Welling:
- Emergency Plumber in Welling
- Burst Pipes in Welling
- Leak Detection in Welling
- Blocked Drains in Welling
- Toilet Repairs in Welling
- Tap Repair & Installation in Welling
- General Plumbing in Welling
- Bathroom Plumbing in Welling
- Washing Machine & Dishwasher Installation in Welling
- Boiler Repair in Welling
- Boiler Servicing in Welling
- Boiler Installation in Welling
- Central Heating Repair in Welling
- Commercial Plumbing in Welling
Related guides
- New Homeowner Plumbing Guide — London 2026
- London Hard Water — The Complete Homeowner & Landlord Guide 2026
- How to Read a Plumbing Quote — A London Homeowner’s Guide 2026
- London Plumbing Costs & Compliance Guide 2026
The kitchen is where your plumbing meets your drinking water, so the details that matter are compliant wastes, correctly protected feeds and a suitable drinking-water supply. Testing before the units are closed reduces the risk of concealed leaks and poor drainage.
Contact verified plumbers in Welling ↑
*Last reviewed: July 2026 by Adiel Khan — SFEDI-accredited business advisor, 20+ years’ experience (South East Enterprise Ltd) and operator of VerifiedPlumbers. LinkedIn ↗*
This page is checked for compliance and regulatory accuracy against the bodies cited on it — the Water Supply (Water Fittings) Regulations 1999, the Drinking Water Inspectorate, Thames Water, Part P / BS 7671, GOV.UK and TfL. Source links are provided within this page where relevant.
Sources & further reading
1. Water Supply (Water Fittings) Regulations 1999, Schedule 2 (conveniently situated wholesome drinking-water tap) — https://www.legislation.gov.uk/uksi/1999/1148/schedule/2/made
2. Drinking Water Inspectorate — water hardness / hard water and softeners — https://www.dwi.gov.uk/consumers/learn-more-about-your-water/water-hardness-hard-water/
3. Thames Water — hard water guidance — https://www.thameswater.co.uk/help/water-and-waste-help/water-quality/hard-water
4. Water Supply (Water Fittings) Regulations 1999, Schedule 2 — backflow prevention — https://www.legislation.gov.uk/uksi/1999/1148/schedule/2/crossheading/backflow-prevention/made
5. Thames Water — misconnected pipes — https://www.thameswater.co.uk/help/home-improvements/misconnected-pipes
6. GOV.UK — Approved Document P: electrical safety in dwellings — https://assets.publishing.service.gov.uk/media/5a802da7ed915d74e622ceed/BR_PDF_AD_P_2013.pdf
7. Transport for London — Ultra Low Emission Zone — https://tfl.gov.uk/modes/driving/ultra-low-emission-zone
8. GOV.UK — Building Regulations approval: when approval may be needed — https://www.gov.uk/building-regulations-approval